30¢ Compression Clay from PI - Final Last Poll (Text)

Garyon · #31 (**permalink**) 06-02-2008, 10:11 PM

Sorry I have been quiet ... been pretty busy with non-chip related things this weekend. Does anybody have the specs required by Joe for the final production image? Artwork dimensions, resolution, etc ... ?

Gary

Felt Lizard · #32 (**permalink**) 06-02-2008, 10:17 PM

Dunno. I'll email Joe with a link to this thread.

palmimports · #33 (**permalink**) 06-03-2008, 12:10 AM

Quote:

Originally Posted by Felt Lizard

Dunno. I'll email Joe with a link to this thread.

sorry for the delays- wife just had back surgery so its been a rough few days
artwork for the chips: actual diameter will be 1.103 inches so the artwork with bleed should be around 1.110 inches

anything GOOD will work- even a GOOD jpg but China prefers AI files if prossible or an EPS

Each file MUST be an indiviual file and round.

Ill do mockups at work and check for color matching prior to sending em over

I'm stoked here- looking forward to this and I am SO appreciative to all who made this happen- hats off to all of you who did what I would have never gotten done

Garyon · #34 (**permalink**) 06-03-2008, 10:31 AM

Quote:

Originally Posted by palmimports

sorry for the delays- wife just had back surgery so its been a rough few days
artwork for the chips: actual diameter will be 1.103 inches so the artwork with bleed should be around 1.110 inches

anything GOOD will work- even a GOOD jpg but China prefers AI files if prossible or an EPS

Each file MUST be an indiviual file and round.

Ill do mockups at work and check for color matching prior to sending em over

I'm stoked here- looking forward to this and I am SO appreciative to all who made this happen- hats off to all of you who did what I would have never gotten done

I am afraid a Photoshop document is the best I can do. Every time I open AI my head swims at the prospect of starting over and learning a new software application, especially one so complicated. I thought more of what I learned in Photoshop would transfer but ... I guess it's that whole "Old Dog, New Tricks" problem! - sigh

Anyway ... I will have the files ready and sent to you in the next day or two!

Felt Lizard · #35 (**permalink**) 06-03-2008, 11:27 AM

Garyon, any chance you could throw a quick mock up of the 9 in here?

With that, Dicecaller can get the interest thread rolling while you guys kick around the specifics....

palmimports · #36 (**permalink**) 06-03-2008, 11:32 AM

Quote:

Originally Posted by Garyon

I am afraid a Photoshop document is the best I can do. Every time I open AI my head swims at the prospect of starting over and learning a new software application, especially one so complicated. I thought more of what I learned in Photoshop would transfer but ... I guess it's that whole "Old Dog, New Tricks" problem! - sigh

Anyway ... I will have the files ready and sent to you in the next day or two!

LOL tell me- I have to work in both but AI can be a hairball at times-
PSD is fine- just make sure each image is on the same canvas/document size as the artwork file- a 1.110 inch ROUND file with transparent backround is good and a doc size of the same 1.110 inch will work.

Garyon · #37 (**permalink**) 06-04-2008, 02:25 AM

Final (?) comps and mock-ups ... I added some larger images of each chip so the inlay detail could be seen a little more clearly. Of course, any/all these images may be used in an Interest thread for the group buy.

The inlay files have been submitted to Joe ... we're off and running!!